broker

Allows you to route messages to multiple child outputs using a range of brokering patterns.

Common
Advanced

# Common config fields, showing default values
output:
  label: ""
  broker:
    pattern: fan_out
    outputs: [] # No default (required)
    batching:
      count: 0
      byte_size: 0
      period: ""
      check: ""

# Advanced config fields, showing default values
output:
  label: ""
  broker:
    copies: 1
    pattern: fan_out
    outputs: [] # No default (required)
    batching:
      count: 0
      byte_size: 0
      period: ""
      check: ""
      processors: [] # No default (optional)

Processors can be listed to apply across individual outputs or all outputs:

output:
  broker:
    pattern: fan_out
    outputs:
      - resource: foo
      - resource: bar
        # Processors only applied to messages sent to bar.
        processors:
          - resource: bar_processor

  # Processors applied to messages sent to all brokered outputs.
  processors:
    - resource: general_processor

Fields

`copies`

The number of copies of each configured output to spawn.

Type: int

Default: 1

`pattern`

The brokering pattern to use.

Type: string

Default: "fan_out"

Options: fan_out , fan_out_fail_fast , fan_out_sequential , fan_out_sequential_fail_fast , round_robin , greedy .

`outputs`

A list of child outputs to broker.

Type: array

`batching`

Allows you to configure a batching policy.

Type: object

# Examples

batching:
  byte_size: 5000
  count: 0
  period: 1s

batching:
  count: 10
  period: 1s

batching:
  check: this.contains("END BATCH")
  count: 0
  period: 1m

`batching.count`

A number of messages at which the batch should be flushed. If 0 disables count based batching.

Type: int

Default: 0

`batching.byte_size`

An amount of bytes at which the batch should be flushed. If 0 disables size based batching.

Type: int

Default: 0

`batching.period`

A period in which an incomplete batch should be flushed regardless of its size.

Type: string

Default: ""

# Examples

period: 1s

period: 1m

period: 500ms

`batching.check`

A Bloblang query that should return a boolean value indicating whether a message should end a batch.

Type: string

Default: ""

# Examples

check: this.type == "end_of_transaction"

`batching.processors`

A list of processors to apply to a batch as it is flushed. This allows you to aggregate and archive the batch however you see fit. Please note that all resulting messages are flushed as a single batch, therefore splitting the batch into smaller batches using these processors is a no-op.

Type: array

# Examples

processors:
  - archive:
      format: concatenate

processors:
  - archive:
      format: lines

processors:
  - archive:
      format: json_array

Patterns

The broker pattern determines the way in which messages are allocated and can be chosen from the following:

`fan_out`

With the fan out pattern all outputs will be sent every message that passes through Redpanda Connect in parallel.

If an output applies back pressure it will block all subsequent messages, and if an output fails to send a message it will be retried continuously until completion or service shut down. This mechanism is in place in order to prevent one bad output from causing a larger retry loop that results in a good output from receiving unbounded message duplicates.

Sometimes it is useful to disable the back pressure or retries of certain fan out outputs and instead drop messages that have failed or were blocked. In this case you can wrap outputs with a drop_on output.

`fan_out_fail_fast`

The same as the fan_out pattern, except that output failures will not be automatically retried. This pattern should be used with caution as busy retry loops could result in unlimited duplicates being introduced into the non-failure outputs.

`fan_out_sequential`

Similar to the fan out pattern except outputs are written to sequentially, meaning an output is only written to once the preceding output has confirmed receipt of the same message.

`fan_out_sequential_fail_fast`

The same as the fan_out_sequential pattern, except that output failures will not be automatically retried. This pattern should be used with caution as busy retry loops could result in unlimited duplicates being introduced into the non-failure outputs.

`round_robin`

With the round robin pattern each message will be assigned a single output following their order. If an output applies back pressure it will block all subsequent messages. If an output fails to send a message then the message will be re-attempted with the next input, and so on.

`greedy`

The greedy pattern results in higher output throughput at the cost of potentially disproportionate message allocations to those outputs. Each message is sent to a single output, which is determined by allowing outputs to claim messages as soon as they are able to process them. This results in certain faster outputs potentially processing more messages at the cost of slower outputs.